Last month, a peer in the curtain wall business asked me on WeChat about the same school project: the split brick prices quoted by two companies differed by nearly double. Was one of them cutting corners? I asked him to photograph both quotations and send them over, and it became clear at a glance—one quoted sintered split brick, the other quoted flexible split brick. Both are "split brick," but they are actually two completely different materials, and their prices were never in the same range to begin with.
This situation is all too common in the building materials circle. Flexible stone and sintered brick both make this split-face brick texture, and the three words "split-face brick" may refer to completely different things on drawings, in tender documents, and at stalls in building materials markets. If this point is not clarified, all subsequent discussions about price, schedule and acceptance will be misaligned communication.
Flexible stone split brick and sintered split brick are not the same thing
The first type isSintered split brick, also called ceramic split brick or split-face brick. Clay is extruded into shape, fired at high temperature, and then split in the middle of the brick body with a special splitting device, forming two brick faces with rough fractured surfaces. This process determines its texture—the particles and layering of the clay can be seen on the fractured surface, there are subtle undulations to the touch, and when light hits it, it is soft diffuse reflection, not the harsh glare of a mirror surface.
The second type isFlexible split brickIt belongs to a texture category within MCM flexible stone (also called soft porcelain). Its cross-section pattern is not split but pressed with molds and then cured at low temperature. So you can see the "appearance" of split brick, but the hardness, thickness and weight you feel are different.
Both can achieve the appearance of split brick, but their engineering properties differ greatly.Split-face brick category in Product CenterCurrently it is mainly the flexible type, such asSoft porcelain light stone A-01、A-02、A-03, all are flexible split bricks distinguished by block-face texture.
Look at the six dimensions together
| Comparison item | Sintered split brick | Flexible split brick (MCM) |
|---|---|---|
| Thickness of a single piece | Standard 10–14mm | Commonly 2–5mm |
| Unit weight | Approx. 20–30kg/m² | Approx. 3–6kg/m² |
| Water absorption | Generally 3%–6%, which is low water absorption | Depends on the formula; test data must be requested |
| Sources of color difference | Kiln batch, position, and atmosphere; these are natural kiln variations | Batch formula and printing/transfer control |
| Transportation damage | High brittleness, edges and corners prone to chipping | Flexible, low breakage rate |
| Requirements for the substrate | Heavy; high pull-out strength is required. | Lightweight, with little impact on additional load |
The second row and the last row of this table are what deserve the most attention. Sintered split bricks weigh more than twenty kilograms per square meter; adding the bonding layer, for a wall of over a thousand square meters on one side, the extra weight the exterior wall system must bear is tens of tons. This is not just a materials issue; it is a question of whether structural calculations and anchoring schemes must be changed accordingly. Flexible split bricks weigh three to five kilograms per square meter, so the load can basically be considered as that of a "decorative layer."
But being light also comes at a cost. Flexible materials rely on the chemical and mechanical bonding between the adhesive and the substrate. Once the substrate has sanding, hollowing or moisture content exceeding the standard, thin materials have no self-weight "ballast" effect and are instead more likely to bulge over the entire sheet. This will be discussed further below.
Sintered split brick: when you can't avoid it
After thirty years of exterior walls, fired brick has its place. First isProjects with explicit requirements for "genuine materials"——For some government public buildings, cultural buildings and university main buildings, the evaluation for awards and the plan review will explicitly require natural sintered finishes. The second isExtremely durable scenarios; for example, on high-traffic ground-floor wall bases and areas subject to frequent impact and washing, sintered brick is indeed more stable in hardness and wear resistance.
The third isHumanistic characterThe project at Guiyang No. Sixteen Middle School used approximately 16,800 square metres of A-face split brick. The teaching buildings, laboratories, canteen and dormitories across the campus were intended to form a visually coherent whole.Project file for this caseIt mentions that secondary school buildings are of mixed types, with high occupant density, safety sensitivity and clear image requirements—the somewhat matte, substantial surface of sintered brick does not easily show dirt on campus, nor does it easily look cheap; this is the practical reason the design side ultimately chose it.

As scale increases, the management difficulty of sintered bricks rises accordingly. The Qingzhen campus of Guiyang Vocational and Technical College of Transportation is about 22,000 m³, entering the site in multiple batches, constructed by multiple work teams, with a construction period spanning several months. Kiln color variation in sintered bricks is a physical characteristic; even the same formula shows slight differences between kiln batches. A single brick may look fine, but when two batches are applied to the same wall, a dividing line appears under sunlight. Therefore, the key action for such projects is not "choosing a color" but first setting the color code, then scheduling production, and finally delivering in batches by building.
Flexible split brick: where it is more cost-effective
Flexible split brick has been widely used in recent years in old-building renovation and on irregular shapes, mainly for three reasons.
First, old walls cannot bear the weight.Brick-and-concrete buildings from the eighties and nineties of the last century often have loose or hollow external plaster; some also include lightweight partition walls added later. Installing fired brick weighing more than twenty kilograms on such substrates presents a substantial risk. Flexible split brick adds less weight to the substrate and may be more feasible when used with a suitable bonding primer and dedicated adhesive.
The second is irregular shapes and edge closures.At locations such as curved walls, column wraps, waistlines, and window surrounds, sintered brick must either be cut or dry-hung; once cut, the exposed cross-section is very unsightly. Flexible material can be bent directly, with a single sheet running across the corner and a clean finish.
The third is renovation without business interruption.For buildings such as hotels, shopping malls and schools that cannot be shut down for long periods, flexible materials allow construction by zone and in stages, generate no large amount of construction waste, and do not require large scaffolding to occupy space for long periods.

Three places where mistakes are easily made
Pitfall one: comparing only unit prices, not system costs.The unit price of sintered brick may look high, but if the substrate conditions are good and it can be completed in one pass, the overall cost may not be high; the unit price of flexible brick may look low, but if the substrate needs to be completely removed and redone, requires full skim coating for leveling, and requires additional waterproofing, the system cost will exceed it. When requesting a quote, you must ask clearly: whether substrate treatment is included, whether jointing agent is included, whether scaffolding is included, and what percentage the loss rate is calculated at.
Pitfall Two: Using a sample of flexible brick to benchmark against sintered brick.The cross-sectional texture of the two is not on the same order of magnitude. Viewed up close, the texture of flexible brick is "printed" on, and the sharpness of the edges and the depth of the holes are not as natural as those of sintered brick. From three to five meters away there is basically no difference, but if it is a wall surface within reach, the client will notice a discrepancy as soon as they touch it. During the selection stage, be sure to make a full-scale on-wall mockup; do not just look at a sample block of A4 size.
Pitfall three: leaving joints according to old experience.Sintered brick conventionally leaves joints of 8–12mm; joint depth and joint width directly affect the "shadow line" of the facade and are key to the character of split brick. The panel size of flexible brick is usually larger than that of sintered brick; if a 10mm joint is copied directly, the facade will look sparse. Joint width should follow the panel size and layout; produce a layout drawing first and then determine joint width—do not snap lines on site based on feel.
Pitfall Four: Treating the loss rate as a trivial matter.The layout waste of split-face brick is higher than imagined. Positions such as windows, corners, and waistlines all require cutting bricks. The actual waste for a building is usually 5%–8%, and buildings with many irregular shapes can reach 10% or more. Flexible materials can be applied in whole sheets, and the cut-off edges and corners can still be used on small surfaces, so the waste is generally lower, but do not stock up based on 3%. Secondary replenishment caused by insufficient stock is often the same problem as color difference between new batches—the batch that comes back is no longer the original color number.
The four lines that truly need to be aligned on a quotation
Put the two quotations side by side, and first do not look at the total price; look at these four lines.
The first row is the material unit price and the measurement basis.Some quote by square meter, some quote by piece and then convert, and others list joint filler and adhesive separately as auxiliary materials. With different scopes, total prices cannot be compared. The most absurd quotation I have seen had a unit price thirty percent lower, and only when I turned to the last page did I discover that the adhesive was billed separately by "set," with one set covering exactly two square meters.
The second line is substrate treatment.This item is the easiest to hide. Old walls need to be removed, repaired, and coated with interface agent—a cost of tens of yuan per square meter—and whether it is written into the quote makes a big difference. When asking for a quote, ask directly: does this price include removal and leveling? If the other party hesitates, the answer is basically clear.
The third line is wastage and stock.Does the quotation include loss, at what percentage is the loss calculated, and how are the price and lead time for replenishment determined? If these three points are not written into the contract, there will be endless disputes later. Especially for projects with locked color numbers, the replenishment clause is equivalent to leaving yourself a way out.
The fourth line covers the warranty and the boundaries of responsibility.How many years is the warranty, what does it cover (how are detachment, cracking and fading each classified), who attends the site when a problem occurs, and how soon will they arrive. For finishes such as split-face brick, detachment is a safety liability, not an aesthetic issue; this must be clearly stated in writing in this industry. Verbal promises are meaningless.
Layout drawings are more important than samples
Many people think that once the sample is settled, everything is fine. In reality, about seventy percent of the character of a split-brick facade comes from the layout: where the starting point is, how the edges by the windows are finished, whether the waistline presses against the joints, and whether the internal and external corners use whole bricks or cut bricks. With the same batch of bricks, two different layouts can produce results that differ by a whole grade.
The standard practice is to produce a layout drawing before construction, laid out according to the actual wall dimensions, marking the position and cutting line of each tile. The layout drawing must be signed and confirmed by the construction, design, and execution parties, and the site must be constructed according to the drawing. Starting installation without a layout drawing will inevitably end with discovering half a tile left when reaching the window, and then relying on workers to improvise on site—this is not the workers' problem, it is a management problem.
The panel size of flexible split brick is usually larger, and the continuity of the texture must also be considered during layout. If the texture on the same wall extends horizontally and the starting point is chosen incorrectly, obvious texture misalignment will appear at the joints, looking from a distance like a horizontal line drawn across the wall.
How to inspect on site: just focus on these items
- Check the same batch.When unpacking, check the batch number; the same facade must use the same batch. For materials entering the site in batches, require the supplier to provide a sealed color-number sample for on-site comparison.
- Measure the substrate.Use a pull-off tester to perform on-site pull-off testing. Flexible materials generally require a tensile bond strength to the substrate of no less than 0.4MPa; refer to the design documents and product instructions for specifics.
- Check the flatness.Inspect with a 2 m straightedge; control the finish flatness deviation in accordance with the finish tile works requirements of GB 50210-2018. Do not substitute "it looks fine" for actual measurement.
- Tap for hollow areas.7 days after completion, tap each piece with a small hammer. The hollow area of each individual piece and the hollow ratio per natural room must meet the acceptance standards. Rework immediately upon finding hollow areas; do not wait until handover.
- Check the jointing.Seams must be full, continuous, and free of cracks; after the pointing mortar cures, it should not come off with a simple pick. In humid areas, confirm the water resistance of the pointing mortar.
Several frequently asked questions
Can flexible split brick be used outdoors, and will it fade under sun and rain?
It can be used outdoors, provided that the correct exterior wall model is selected and the artificial weathering aging data are checked. Require the supplier to provide the test report for the corresponding model, and check clearly whether the sample name, specifications, and client in the report match the goods you intend to buy. The report is generic and the product is customized; if these two do not match, the report is just a piece of paper.
Can the two types of tiles be mixed on one building?
Technically it is possible, but use it with caution. The hue, gloss, and joint shadows of the two materials are completely different, and the junction will create a noticeable "seam effect." If you do need to mix them, it is recommended to use horizontal layering such as "sintered stone for the base and flexible stone for the upper part," rather than vertical splicing within the same visual plane.
For old-wall renovation, should the original tiles be stripped?
Check three conditions: whether the original tiles have hollow spots or have fallen off, whether the adhesive layer is firm, and whether the surface has oil stains or release agents. If all three pass, the interface can be treated and the material applied directly; if any one fails, partial or full removal is safer. A separate article on specific renovation methods for old walls will follow; this is not covered here.
Back to the question at the beginning: two quotes differing by a factor of two isn't about who is cheating whom—they are two different things. Once you're clear whether you want sintered or flexible, the price naturally returns to a comparable track.
For the actual product, please refer toSplit-face brick product pageFor actual engineering results, seeEngineering cases; testing and qualification documents are inHonors and qualificationsThe page can be queried.


WhatsApp
Guangdong Public Network Security Preparation No. 44200002005257