Real stone paintalso calledStone imitation paintor stone paint, which falls within the scope of synthetic resin emulsion sand-textured architectural coatings, except that the aggregate gradation used in the coating is more reasonable than that of previous colored-sand coatings, the colors are richer, the shapes are more realistic, the application method is more refined, and the application range is wider. Real stone paint is an architectural coating product with relatively strong artistic texture.
I. Construction tools:
1. Scaffolding: The scaffolding should be 30-40 cm away from the wall to be sprayed. There should be no horizontal water pipes against the wall, and the wall must not have scaffold holes. Hanging baskets and bridging are recommended. When using bamboo scaffolding, pay attention to leaving an appropriate working distance during application.
2. Power above 5KW, sufficient air volume, pressure of 0.5-1.0 MPa, an air compressor with three air pipes, capable of supporting more than three people working simultaneously, with automatic pressure control.
3. Spray gun: top-cup spray gun, capacity 500ml, nozzle diameter 1.3mm or above. The capacity should not be too large, as it is inconvenient to operate; if the nozzle diameter is small, the construction speed will be slow, making it unsuitable for large-area construction.
4. Nozzles of various calibers: 4mm, 5mm, 6mm, 8mm, etc. The smaller the caliber, the flatter and more uniform the spray; the larger the caliber, the larger the speckles and the stronger the textured effect.
5. One set of airless spray gun.
6. Rubber hose: oxygen hose, diameter 8mm.
7. Several brushes, rollers, and putty knives.
8. Masking tools: plastic sheeting, fiberboard, thumbtacks, tape.
Real stone paintthe construction process:
① For the acceptance of the plastered base, hollowing and cracks on the wall surface shall be reworked by the plastered base party. Clean the wall surface of floating sand, sand particles and other debris; the wall surface should be maintained for one to two weeks, with pH < 10.
② Mark lines and lay out the grid according to the design requirements, set out with black lines, and mask with adhesive tape. To ensure the lines are straight and level, use a master template as the marking guide. In addition, seal off the areas of the wall surface that are not to be painted with adhesive tape and film to prevent contamination.
③ Apply the elastic putty by trowel. This product is a two-component product: pour both components from the packaging into a container and stir thoroughly into a uniform paste-like mortar with no granules and no sediment, then set aside for use. Apply the above paste-like mortar directly to the substrate with a trowel, with the consumption controlled within 2 kg/㎡. Once the putty is completely dry (about 24 hours), proceed to the next process.
④ Roll on one coat of alkali-resistant primer. Roll evenly, in a consistent direction, with no marks at the joints between the upper and lower coats, and with a consistent color.
⑤ Begin spraying in two passesReal stone paint,air pressure is generally 0.6-0.8MPa. During spraying, items not to be sprayed need to be covered with newspaper or completely isolated with tape. The consumption is about 5kg/ m2 or so.
⑥ Remove the adhesive tape immediately after spraying. Remove the tape carefully so as not to affect the cut edges of the coating film. To remove, pull upward as much as possible, not forward.
⑦ After the real stone paint has hardened, theReal stone paintThe sharp edges of the surface particles are ground down by about 30-50%, which enhances aesthetics, reduces sharpness and prevents dust accumulation.
⑧PendingReal stone paintAfter fully hardening, the topcoat can be applied by roller or spray.
⑨Inspect the sprayed wall surface; any problems found shall be corrected promptly, and the site shall be cleaned and swept.
Construction processes for real stone paint in different colors:
1. White and light-coloredReal stone paintConstruction: First apply one coat of white cement to the wall, which must be level and free of obvious trowel marks; or directly apply a colored liquid primer, then spray the middle coat and top coat as specified;
2. Dark-coloredReal stone paintConstruction: Spray the primer as specified. When applying the middle coat, only a thin coat is needed, with the thickness controlled at 1–2mm, then apply the top coat.
All of the above comes from Zhongshan City.FLATBuilding Materials Co., Ltd. If reproduced, please indicate the source: http://wwwzsfulaitei.com


WhatsApp
Guangdong Public Network Security Preparation No. 44200002005257