Water-in-water, precautions and common problem solutions during water-in-sand construction

Release: Common questionsFLAT Official Website

1st note: The base layer uses special putty, gray putty mortar, and traditional white putty is not recommended. The composition is gray silicate cement...

Precaution One: The substrate must use a dedicated putty, which is a gray putty mortar; traditional white putty is not recommended. A gray putty composed mainly of gray Portland cement and acrylic polymer has good adhesion, filling properties (low shrinkage), crack resistance and workability, with a certain strength and hardness, moderate drying time (surface dry and hard dry), and is easy to apply and sand. In the application of water-in-water multicolor coatings, it is clearly felt that gray putty mortar has more advantages than white putty mortar. Putty sanding is also a key step. During the day, the putty is sanded block by block using a dedicated sanding frame, so that the wall surface is leveled to a uniform flatness after sanding; at night, a sun lamp can be used to shine obliquely to check the divided wall surface, and any uneven areas found should continue to be sanded. If an area cannot be sanded well at that time, mark it with a marker pen and repair it with putty; after it dries thoroughly, sand it again, requiring the flatness of each block to be flat and even. The watering and curing time is about 24 hours, and the next process can only proceed after it dries thoroughly.

Precaution Two: When making the litchi surface effect, most manufacturersWater-in-waterMulticolor coatings require a textured aggregate base coat before spraying the multicolor coating; when creating a flamed-slab effect,Water-in-waterMulticolor coatings require a colored-sand real-stone paint base coat before spraying the multicolor coating; this gives an obvious sensory effect, but the texture or colored-sand real-stone paint used will more or less be exposed on the outside. Both materials are mainly composed of crushed stone, with uneven surfaces and countless fine pores on the product surface; due to the phenomenon of air re-adhesion, dust and dirt will inevitably adhere to the wall surface and cause local contamination. Of course, under the protection of the topcoat, rainwater washing can restore the original appearance. Some also prefer an elastic intermediate coat as the base coat, using a dedicated elastic intermediate coat to increase the film thickness for waterproofing and crack resistance of the wall (the main purpose of this process is to increase film thickness and improve crack resistance and waterproofing).

Precaution Three: The primer must be applied thoroughly, and no dead corners may be missed, especially the side edges of door and window openings, lines and the inner corners of waistlines (when color matching), etc.; otherwise, after the main material spraying is completed, when the protective film is torn off or the masking tape is peeled off, at that areaWater-in-waterMulticolor coatings are prone to edge curling, which in turn easily leads to frayed edges.

Precaution Four:Water-in-waterDuring the spray application of multicolor coatings, suspended-platform construction should be adopted as much as possible; for special parts, it is best to have two people, one holding a baffle and the other spraying the multicolor coating, so that with such cooperation the multicolor coating will be sprayed more evenly. If the sprayer has to hold the baffle and spray the coating at the same time, it is difficult to keep the distance between the spray gun and the wall stable. Rope-suspended construction must not be used for the spray application of water-in-water multicolor coatings; with the distance varying from far to near, it is very difficult to spray evenly, and spray mottling is very likely to occur.

Precaution Five: When the wall surface becomes blotchy due to uneven construction and needs repair, the same work area must be repaired at the same time, such as several grid blocks or one facade; do not repair only where blotchiness is visible, as this may make it more blotchy;Water-in-waterDuring the construction of multicolor coatings, please be sure to pay attention to the weather forecast. When spraying multicolor coatings, the second coat can only be sprayed after the first coat has dried, with a general interval of 12 hours; after the multicolor coating has been sprayed, at least 24 hours must pass before the topcoat can be applied. Also note that after the topcoat is applied, ensure that there is no continuous rain or heavy rain within one week.

Precaution Six:Water-in-waterMulticolor coatings must not be stirred vigorously, must not be diluted with water, and must not be mixed with other substances; opened multicolor should be used up in one go as much as possible; when applying flat water-in-water multicolor coatings, withTextured paint、Real stone paintCompared with a colored-sand base coat or an elastic mid-coat base, the surface is much smoother, so when applying the multi-color coating in one pass, the spray gun should be moved faster to prevent sagging.

Precaution Seven:Water-in-waterMulticolor coatings require a clear topcoat; without a clear topcoat, the multicolor paint film is not dense, and its anti-aging, weather resistance, anti-chalking and color retention effects will be greatly reduced. When applying the clear topcoat, to conceal uneven thickness during application, a matte clear topcoat is recommended. In addition, for European-style building components, to avoid the mottling caused by roller-applied topcoat, spray application is recommended.

Precaution Eight: For the construction of the inner and outer corners of flying eaves, pay attention: the outer corner should be covered within the entire spraying fan surface, and do not worry about using more material, so that it can be sprayed evenly; for the inner corner, simply treat it as a flat surface, and do not artificially think that the position is difficult to spray and first give it a sweep spray before spraying the whole surface, as this easily makes the coating too thick. In short,Water-in-waterFor the treatment of internal and external corners with multicolor coatings, the key is not to worry about using more material; simply make the up-and-down and left-and-right strokes of the gun larger.

◆ Water-based multicolorStone imitation paintConstruction

1. Construction environment conditions

When applying water-based multicolor stone-imitation coatings, suitable climatic conditions should be selected for topcoat spraying. Suitable climatic conditions are: construction conditions of temperature above 20℃ and relative humidity below 85%; temperature above 10℃ and relative humidity below 80%; temperature above 5℃ and relative humidity below 60%.

2. Preparation of coating equipment

For water-based application, use a dedicated Japanese-imported multicolor spray gun; the spray gun is an Iwata W77 model, with a nozzle diameter generally of 2.5mm, air compressor pressure of 0.4-0.8mpa, and air displacement >0.25m3/min. A capacity of 2L-10L is a commonly used construction tool. For ease of movement and use, a single-phase (220V) lightweight model can be used. In addition, rollers, paint brushes, putty scrapers, material scoops, labor protection supplies, etc. should be prepared.

Detailed explanation of construction methods and construction issues for granite coatings and multicolor paints

3. Treatment of construction substrate

Remove loose dust, loose material, oil stains, and grind protruding parts flat. For walls with efflorescence, scrub with a 5% dilute hydrochloric acid solution, then rinse with clean water, and allow to dry naturally for more than 72 h. On fiberboard and wood panels, apply rust-preventive treatment to nail heads, and cover panel joints by pasting with thin diagonal strips of polyester cloth.

For new walls (cement mortar, hemp-fiber, paper-strip lime plaster rendering), one week in summer and more than 10 days in winter (moisture content 10%, PH value below 905); for uneven surfaces of old walls, fill and level with putty, and sand the old paint film surface with No. 0 to No. 1 abrasive cloth. For the application methods of primer and intermediate coats, roller application may be used; brush application shall be used to touch up edges and corners that cannot be reached by roller, with no omissions.

4. Other precautions during construction

A. Before opening the coating bucket, first shake it or roll it in a circle, then open the lid, and stir evenly with a wooden stick;

B. Check the spraying equipment, start the air compressor to inflate, adjust the air pressure to 0.35-0.4mpa, connect the multicolor spray gun with a rubber hose, and perform a test spray with an empty gun, observing whether the pressure is within the effective pressure range (0.25-0.35mpa);

C. After filling the spray gun with multicolor paint, first test-spray on a test panel to adjust the paint output and air output to a suitable level, then move to the construction substrate for spraying. Hold the spray gun perpendicular to the surface to be coated, at a distance of 30-1000PX from the wall, and apply in a crisscross pattern at right angles vertically and horizontally. Move steadily; do not stop and go or skip ahead, so as to avoid defects such as material buildup, sagging and unevenness;

D. When spraying wall corners and turning corners, first mask 10-500PX near the corner of one wall, and after spraying is completed, mask the other side, to avoid excessively dense patterns at the corner.

E. Control the spraying amount well. Excessive spraying will cause sagging and blurred patterns; too little will make the patterns appear scattered, the surface rough, and the coating performance indicators low. Therefore, the paint amount should be 3-5m2/kg.

Common Questions and Cause Analysis

During the promotion of water-based multicolor coatings, many coating manufacturers or coating application companies have promised real estate developers or customers that their water-based multicolor architectural coatings can last more than 10 years. Due to the small spray volume per unit area and the thin coating thickness itself, how to meet the requirements for waterproofness, crack resistance, durability and stain resistance cannot be fully solved by the water-based multicolor coating alone; it needs to be solved through the coating system. Through the technical application of Lishiwei Paint in recent years, the following common problems in the current market application of water-based multicolor coatings have been summarized.

1. Common effect types in the water-based multicolor coatings market

One type is the flat type: it mainly involves spraying water-based multicolor coating on a flat exterior wall coating; the surface is relatively flat and smooth, presenting a flat-type granite effect;

The second category is the lychee-textured type: mainly applied by directly spraying multicolor water-in-sand, or with elastic textured coating orReal stone paint。、Textured paintApply a base coat, then spray a water-based multicolor coating on top to achieve a litchi-textured (or rough) finish.

The third category is brushed strip-shaped: mainly used for interior decoration and artistic flooring, with a flat and smooth surface, primarily imitating ceramic tile stripes and presenting a unique visual effect that natural marble does not have.

The fourth category is the limestone ground-finish effect: it is mainly used for interior and exterior decoration; the surface is ground again to present a unique texture different from the flat surface or matte surface of water-in-water coatings, with a high degree of aesthetics.

2. Cracking of wall coating

How to improve the crack resistance of the coating is a major problem to be solved. In terms of coating thickness, the putty layer comes first, followed by the base color paint layer and the water-based multicolor coating, then the primer layer and the clear topcoat layer. The crack resistance of the entire water-based multicolor coating system can be improved by increasing the thickness and crack resistance of each coating layer. Increasing the thickness of the base color paint layer can improve the crack resistance of the coating, but the cost is high; increasing the thickness of the water-based multicolor coating, that is, full-coverage spraying, also increases the cost and places higher requirements on water whitening resistance. Improving the crack resistance of the coating by improving the crack resistance of the putty layer offers good cost-effectiveness for this type of construction.

3. Water resistance of elastic coating

At present, flat-type water-based multicolor coatings generally use elastic flat coating as the base coat, while litchi-texture coatings use water-in-sand direct spraying or elastic textured intermediate coating as the base coat. While improving the crack resistance of the coating, the initial water resistance of the coating needs to be properly addressed to avoid blistering and whitening caused by rain.

4. Quality of water-based multicolor coatings

At present, whether foreign protective colloids or domestic protective colloids, requirements can be met through formula adjustment and additive optimization. The key is whether the raw material selection is reasonable; the stability between raw material batches has a great impact on product quality. The technology of many manufacturers comes from suppliers, but manufacturers that solve the problems of water whitening resistance, storage stability, reproducibility, and repairability of products.

5. Water resistance and whiteness

Because the water-based multicolor coating system uses a large amount of hydrophilic raw materials, the problem of whitening upon contact with water is unavoidable. Pure acrylic or modified styrene-acrylic emulsion with good water-whitening resistance should be selected, rather than casually choosing ordinary elastic emulsion. At the same time, the selection of cellulose, protective colloid and additives and the optimization of formulation design are very important; these can moderately reduce the degree of whitening. Another method is to solve it through clear coating: by selecting a silicone-acrylic emulsion clearcoat that itself has good water-whitening resistance, good sealing properties and breathability, the problem of whitening upon contact with water can be improved.

6. Paint surface gloss

ForReal stone paint、Textured paintWater-based multicolor coating with a lychee-textured imitation fired-slab effect used as a base coat, becauseReal stone paint、Textured paintIt is sand-wall type; the coating surface has many voids and low surface gloss. When water-based multicolor coating is sprayed onto its surface, the areas with multicolor dots have high surface gloss, while the areas without multicolor dots have low gloss. Although a clear topcoat has been applied for sealing, the gloss difference still exists. To solve this phenomenon, many manufacturers use matting to bring the gloss of the two closer, while more manufacturers are researching sand-added water-based multicolor coatings. This not only solves the gloss problem but also has higher compatibility with stone. This has become one of the market application types of water-based multicolor coatings.

Party and information verification

Party:Guangdong Fulaite Building Materials Co., Ltd. · FLAT. / Company Introduction

When the text involves standards, inspections or material parameters, please verify against the original materials listed in the text and the corresponding product conditions. The original samples and reports can bePage of qualifications and inspection reportConsult; models, batches, and project conditions are different, and relevant data should be confirmed separately.

For engineering cooperation and import and export procurement, you can provide the location, required area and intended texture,Contact FLAT for samples and quotes。

FLAT · Guangdong Fulaite Building Materials Co., Ltd.

Make architecture more beautiful.

Focus on flexible stone (MCM soft stone/soft porcelain), providing texture selection, product information and order production coordination.

Copyright © 2012-2026 Guangdong Fulaite Building Materials Co., Ltd. All Rights Reserved Yue ICP No. 16084041

Headquarters Address:No. 2, West of Tong'an Avenue, Dongfeng Town, Zhongshan City, Guangdong Province
Public Security RecordGuangdong Public Network Security Preparation No. 44200002005257