Collection of common problems with water-in-water multicolor coatings

Release: Common questionsFLAT Official Website

How to deal with water-in-water spray flowers? Remove the spray flower area to the putty layer, clean it up and it can be sprayed again, pay attention to protect other completed areas, and avoid secondary pollution. 02 Water-in-water...

01Water-in-waterWhat should I do if overspray occurs?
Strip the spray-spatter area down to the putty layer; after cleaning, spraying can be carried out again. Take care to protect other completed areas to avoid secondary contamination.

02Water-in-waterWhat causes joint marks?
This may be caused by uneven spraying of the water-in-water coating, or by insufficiently flat substrate preparation. The currently effective solution is to carry out construction in sections.


03Water-in-waterWhy is it not suitable for storage?
Water-in-water multicolor is a material in which water-based latex particles are dispersed in an emulsion medium but do not merge with each other. Whether of the encapsulation type or the reaction type, due to the volatilization of the film-forming components, the merging of the color particles is only a matter of time. Finished water-in-water products can be stored for more than 10 days, while inferior products will show phenomena such as stratification and mildew in less than a week of storage.

04Water-in-waterWhat should be done if the particles are too soft during the preparation of multicolor coatings?
The powder content may be appropriately increased according to actual conditions. At present, a more effective method is to select an emulsion with a higher vitrification temperature for formulation, which can increase particle hardness. Second, other additives may be added, such as a small amount of silica sol; the specific effect needs to be tested according to actual conditions.


05Water-in-waterWhat happens if the emulsion content in multicolor coatings is low?
If the emulsion content of water-in-water coating is low, product properties such as color retention, UV resistance, and adhesion will all be reduced accordingly; conversely, if there is too much emulsion, the wall may be slow to dry after application.

06 How to controlWater-in-waterColor dot size?
Observe the size of the color particles; if the color particles are too small, they must be re-produced. The size of the color particles in water-in-water coatings depends on the stirring and dispersing speed during particle formation. Set the rotation speed according to the specific color requirements, follow the high-frequency, multiple-pass method, and observe and adjust the shape of the color particles; if the sprayed dots are rather small, the spray gun pressure may be appropriately increased and spraying performed again.


07Water-in-waterHow to solve cracking caused by thick spraying?
Water-in-water multicolor coatings use color particles made from emulsion and color paste. After film formation, the elastic coefficient is very high; the greater the thickness, the better the crack resistance, and cracking occurs only when the film thickness is relatively thin.

08Water-in-waterCan multicolor coatings be used without a topcoat?
Water-in-water multicolor coating is exposed to complex outdoor environments and can provide good protection for the main coating, offering UV resistance, increased adhesion, and improved weather resistance, yellowing resistance, and so on. The use of a dedicated water-in-water topcoat is recommended.

Party and information verification

Party:Guangdong Fulaite Building Materials Co., Ltd. · FLAT. / Company Introduction

When the text involves standards, inspections or material parameters, please verify against the original materials listed in the text and the corresponding product conditions. The original samples and reports can bePage of qualifications and inspection reportConsult; models, batches, and project conditions are different, and relevant data should be confirmed separately.

For engineering cooperation and import and export procurement, you can provide the location, required area and intended texture,Contact FLAT for samples and quotes。

FLAT · Guangdong Fulaite Building Materials Co., Ltd.

Make architecture more beautiful.

Focus on flexible stone (MCM soft stone/soft porcelain), providing texture selection, product information and order production coordination.

Copyright © 2012-2026 Guangdong Fulaite Building Materials Co., Ltd. All Rights Reserved Yue ICP No. 16084041

Headquarters Address:No. 2, West of Tong'an Avenue, Dongfeng Town, Zhongshan City, Guangdong Province
Public Security RecordGuangdong Public Network Security Preparation No. 44200002005257